| MEDA |
MEDIA FOR WHICH DESIGNED |
HYDRAULIC FLUID SINGLE RESPONSE AND FUEL/OIL, HYDROCARBON SINGLE RESPONSE AND OIL, LUBRICATING, DIESTER BASE SINGLE RESPONSE |
| CRWL |
INSIDE SURFACE CONDITION |
SMOOTH |
| AAGR |
CROSS-SECTIONAL SHAPE STYLE |
ROUND |
| CQJX |
NOMINAL THREAD SIZE |
0.437 INCHES 2ND END |
| ADLH |
SECOND END FITTING SPEC/STD DATA |
MS33656 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL |
| AGAV |
END ITEM IDENTIFICATION |
AIRCRAFT,B-2 BOMBER |
| CRXX |
MEASURING METHOD AND LENGTH |
14.500 INCHES NOMINAL OVERALL |
| THSD |
THREAD SERIES DESIGNATOR |
UNJF 1ST END |
| CRJM |
OUTER COVERING ENVIRONMENTAL PROTECTION |
FUEL RESISTANT AND HYDRAULIC SOLUTION RESISTANT AND CORROSION RESISTANT AND FIRE RESISTANT |
| CRBL |
SECOND END FITTING/COMPONENT AND MATERIAL |
COMPLETE FITTING STEEL, CORROSION RESISTING |
| ACKH |
MINIMUM INSIDE BENDING RADIUS |
2.000 INCHES |
| CRFY |
FLOW ANGLE |
90.0 DEGREES 1ST END |
| AAJD |
THREAD CLASS |
3A 1ST END |
| THSD |
THREAD SERIES DESIGNATOR |
UNJF 2ND END |
| CRFY |
FLOW ANGLE |
90.0 DEGREES 2ND END |
| CQCS |
LAYER COMPOSITION AND LOCATION |
OUTER LAYER MOLDED RUBBER, SYNTHETIC ERR-100 |
| CQBG |
FIRST END SWIVEL ACTION CAPABILITY |
NOT INCLUDED |
| AHNC |
CONNECTION STYLE |
NUT ASSEMBLY WITH GASKET 1ST END |
| CQBD |
BURST TEST PRESSURE |
10000.0 POUNDS PER SQUARE INCH |
| FEAT |
SPECIAL FEATURES |
AS1072 SLEEVE,SILICONE COVERED,WITH CRES BANDS |
| AAJF |
THREAD DIRECTION |
RIGHT-HAND 1ST END |
| ADLG |
FIRST END FITTING SPEC/STD DATA |
MS33656 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL |
| AKUU |
END CONNECTION DESIGN |
ELBOW 1ST END |
| AHNC |
CONNECTION STYLE |
NUT ASSEMBLY WITH GASKET 2ND END |
| ABJH |
TEMP RATING |
65.0 DEG FAHRENHEIT SINGLE RESPONSE AND 500.0 DEG FAHRENHEIT SINGLE RESPONSE |
| CQGM |
MAXIMUM OPERATING PRESSURE |
1500.0 POUNDS PER SQUARE INCH |
| ABKV |
OUTSIDE DIAMETER |
0.375 INCHES NOMINAL |
| AAJD |
THREAD CLASS |
3A 2ND END |
| CRDW |
HYDROSTATIC TEST PRESSURE |
3000.0 POUNDS PER SQUARE INCH |
| AKUU |
END CONNECTION DESIGN |
ELBOW 2ND END |
| ZZZT |
NONDEFINITIVE SPEC/STD DATA |
1 CLASS |
| CQCS |
LAYER COMPOSITION AND LOCATION |
3RD LAYER MOLDED POLYTETRAFLUOROETHYLENE ERR-100 |
| CQCS |
LAYER COMPOSITION AND LOCATION |
1ST LAYER MOLDED POLYTETRAFLUOROETHYLENE ERR-100 |
| ADJM |
INNER CONVEYING TUBE MATERIAL |
PLASTIC, TETRAFLUOROETHYLENE REINFORCED |
| CQBB |
SECOND END RELATIONSHIP WITH FIRST END |
IDENTICAL |
| AARX |
INSIDE DIAMETER |
0.250 INCHES NOMINAL |
| AAJF |
THREAD DIRECTION |
RIGHT-HAND 2ND END |
| ADLF |
HOSE OR TUBING SPEC/STD DATA |
-8005 REV C STANDARD (INCLUDES INDUSTRY OR ASSOCIATION STANDARDS, INDIVIDUAL MANUFACTUREER STANDARDS, ETC.). |
| CRZY |
SECOND END SWIVEL ACTION CAPABILITY |
NOT INCLUDED |
| CQCS |
LAYER COMPOSITION AND LOCATION |
2ND LAYER BRAIDED CORROSION RESISTANT STEEL WIRE ERR-100 |
| CQJX |
NOMINAL THREAD SIZE |
0.437 INCHES 1ST END |
| CQGH |
FIRST END FITTING/COMPONENT AND MATERIAL |
COMPLETE FITTING STEEL, CORROSION RESISTING |
| AWLS |
CONNECTION TYPE |
THREADED INTERNAL HOSE 1ST END |