| CRGD |
POWER DISSIPATION RATING PER SECTION IN WATTS |
0.75 7TH SECONDARY QUALITY |
| AAPN |
SECTION QUANTITY |
1 |
| TTQY |
TERMINAL TYPE AND QUANTITY |
3 PIN |
| ADAT |
BODY WIDTH |
0.180 INCHES MINIMUM AND 0.200 INCHES MAXIMUM |
| AFJN |
FRAGILITY FACTOR |
MODERATELY RUGGED |
| ADAQ |
BODY LENGTH |
1.240 INCHES MINIMUM AND 1.260 INCHES MAXIMUM |
| AXGY |
MOUNTING METHOD |
UNTHREADED HOLE AND TERMINAL |
| CRFJ |
TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS |
-250.0/+250.0 SINGLE SECTION |
| CQGN |
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER |
150.0 SINGLE SECTION |
| CQCK |
ROTARY ACTUATOR TRAVEL IN ANGULAR DEG |
6120.0 MINIMUM AND 9720.0 MAXIMUM |
| TEST |
TEST DATA DOCUMENT |
81349-MIL-R-22097 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL |
| AARG |
RELIABILITY INDICATOR |
NOT ESTABLISHED |
| CBME |
CUBIC MEASURE |
0.079 CUBIC INCHES |
| ABWV |
SHAFT DIAMETER |
0.115 INCHES NOMINAL |
| ZZZK |
SPECIFICATION/STANDARD DATA |
81349-MIL-R-22097/2 GOVERNMENT SPECIFICATION |
| ABTB |
MOUNTING HOLE DIAMETER |
0.088 NOMINAL MILS AND 0.098 NOMINAL CENTIMETERS |
| CRSS |
RESISTANCE TOLERANCE PER SECTION IN PERCENT |
-10.0/+10.0 SINGLE SECTION |
| CSDH |
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER |
85.0 SINGLE SECTION |
| AAQL |
BODY STYLE |
RECTANGULAR W/MOUNTING HOLES/SLOTS |
| CQCM |
CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL |
0.690 NOMINAL MILS AND 0.710 NOMINAL CENTIMETERS |
| CRSX |
ACTUATOR TRAVEL CONTROL FEATURE |
CLUTCH |
| AKPV |
MOUNTING FACILITY QUANTITY |
2 |
| AEFD |
ACTUATOR TYPE |
SINGLE SHAFT |
| ABHP |
OVERALL LENGTH |
1.320 INCHES NOMINAL |
| AEHT |
CENTER TO CENTER DISTANCE BETWEEN TERMINALS |
0.890 INCHES MINIMUM AND 0.910 INCHES MAXIMUM |
| AGTP |
LATERAL DISTANCE BETWEEN MOUNTING HOLE CENTERS |
0.995 INCHES MINIMUM AND 1.005 INCHES MAXIMUM |
| AEDX |
SHAFT STYLE |
ROUND, SLOTTED |
| CSDL |
STANDARD TAPER CURVE PER SECTION |
A SINGLE SECTION |
| ABJT |
TERMINAL LENGTH |
0.469 INCHES MINIMUM AND 0.531 INCHES MAXIMUM |
| ABXF |
SHAFT LENGTH |
0.070 INCHES NOMINAL |
| CQCC |
ELECTRICAL RESISTANCE PER SECTION |
50.0 OHMS C AND BETTER FLOORING |
| ADAU |
BODY HEIGHT |
0.300 INCHES MINIMUM AND 0.330 INCHES MAXIMUM |
| APXH |
TERMINAL LOCATION |
LOWER ADJACENT SIDE SINGLE ROW |