| AAPN |
SECTION QUANTITY |
1 |
| ADAT |
BODY WIDTH |
0.145 INCHES MINIMUM AND 0.185 INCHES MAXIMUM |
| TTQY |
TERMINAL TYPE AND QUANTITY |
3 PIN |
| AXGY |
MOUNTING METHOD |
TERMINAL |
| AFJN |
FRAGILITY FACTOR |
MODERATELY RUGGED |
| ZZZK |
SPECIFICATION/STANDARD DATA |
81349-MIL-R-39035/3 GOVERNMENT SPECIFICATION |
| CQGN |
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER |
150.0 SINGLE SECTION |
| ABXF |
SHAFT LENGTH |
0.050 INCHES MAXIMUM |
| CQCC |
ELECTRICAL RESISTANCE PER SECTION |
50.0 PERCENT, RATED AMPERES C AND BETTER FLOORING |
| CBME |
CUBIC MEASURE |
0.013 CUBIC INCHES |
| AARG |
RELIABILITY INDICATOR |
ESTABLISHED |
| AEDZ |
SHAFT BEARING TYPE |
SLEEVE |
| CRSS |
RESISTANCE TOLERANCE PER SECTION IN PERCENT |
-10.000/+10.000 SINGLE SECTION |
| ADAQ |
BODY LENGTH |
0.230 INCHES MINIMUM AND 0.270 INCHES MAXIMUM |
| AAQL |
BODY STYLE |
RECTANGULAR |
| AARH |
RELIABILITY FAILURE RATE LEVEL IN PERCENT |
0.010 |
| ADAU |
BODY HEIGHT |
0.230 INCHES MINIMUM AND 0.270 INCHES MAXIMUM |
| CQCM |
CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL |
0.100 NOMINAL INCHES |
| ABWV |
SHAFT DIAMETER |
0.060 INCHES MINIMUM AND 0.090 INCHES MAXIMUM |
| ABJT |
TERMINAL LENGTH |
0.172 INCHES MINIMUM |
| CSDH |
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER |
85.0 SINGLE SECTION |
| AEFH |
EFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION |
3600.0 MINIMUM AND 9000.0 MAXIMUM |
| AEHT |
CENTER TO CENTER DISTANCE BETWEEN TERMINALS |
0.200 INCHES NOMINAL |
| CQCK |
ROTARY ACTUATOR TRAVEL IN ANGULAR DEG |
3600.0 MINIMUM AND 9000.0 MAXIMUM |
| AEFL |
MAXIMUM RUNNING TORQUE |
3.00 INCH-OUNCES |
| CRSX |
ACTUATOR TRAVEL CONTROL FEATURE |
CLUTCH |
| TEST |
TEST DATA DOCUMENT |
81349-MIL-R-39035 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL |
| APXH |
TERMINAL LOCATION |
REAR END |
| AEFD |
ACTUATOR TYPE |
SINGLE SHAFT |
| AEFK |
MAXIMUM STARTING TORQUE |
3.00 INCH-OUNCES |
| AEDX |
SHAFT STYLE |
ROUND, SLOTTED |
| ABKW |
OVERALL HEIGHT |
0.230 INCHES MINIMUM AND 0.270 INCHES MAXIMUM |
| CSDL |
STANDARD TAPER CURVE PER SECTION |
A SINGLE SECTION |
| CRFJ |
TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS |
-100.0/+100.0 SINGLE SECTION |
| CRGD |
POWER DISSIPATION RATING PER SECTION IN WATTS |
0.25 7TH SECONDARY QUALITY |