| CRGD |
POWER DISSIPATION RATING PER SECTION IN WATTS |
0.75 7TH SECONDARY QUALITY |
| APXH |
TERMINAL LOCATION |
LEFT ADJACENT SIDE TWO ROWS |
| AAPN |
SECTION QUANTITY |
1 |
| AEFH |
EFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION |
7200.0 MINIMUM AND 15120.0 MAXIMUM |
| TTQY |
TERMINAL TYPE AND QUANTITY |
3 PIN |
| ADAQ |
BODY LENGTH |
0.500 INCHES NOMINAL |
| CQGN |
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER |
150.0 SINGLE SECTION |
| CQCC |
ELECTRICAL RESISTANCE PER SECTION |
50.0 PERCENT, RATED AMPERES C AND BETTER FLOORING |
| ABTB |
MOUNTING HOLE DIAMETER |
0.073 NOMINAL INCHES |
| AARG |
RELIABILITY INDICATOR |
ESTABLISHED |
| AGTP |
LATERAL DISTANCE BETWEEN MOUNTING HOLE CENTERS |
0.520 INCHES NOMINAL |
| AEDZ |
SHAFT BEARING TYPE |
SLEEVE |
| CRFJ |
TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS |
-50.0/+50.0 SINGLE SECTION |
| ABXF |
SHAFT LENGTH |
0.045 INCHES MAXIMUM |
| TEST |
TEST DATA DOCUMENT |
82227-R90135/01 DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
| ADAU |
BODY HEIGHT |
0.500 INCHES NOMINAL |
| CQCM |
CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL |
0.100 NOMINAL INCHES |
| ABJT |
TERMINAL LENGTH |
0.172 INCHES MINIMUM |
| AEFL |
MAXIMUM RUNNING TORQUE |
5.00 INCH-OUNCES |
| AAQL |
BODY STYLE |
RECTANGULAR W/MOUNTING HOLES |
| CSDH |
AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER |
85.0 SINGLE SECTION |
| AEHT |
CENTER TO CENTER DISTANCE BETWEEN TERMINALS |
0.200 INCHES NOMINAL |
| AARH |
RELIABILITY FAILURE RATE LEVEL IN PERCENT |
0.100 |
| CRSX |
ACTUATOR TRAVEL CONTROL FEATURE |
CLUTCH |
| AKPV |
MOUNTING FACILITY QUANTITY |
2 |
| CQCK |
ROTARY ACTUATOR TRAVEL IN ANGULAR DEG |
7200.0 MINIMUM AND 15120.0 MAXIMUM |
| AEFD |
ACTUATOR TYPE |
SINGLE SHAFT |
| AGAV |
END ITEM IDENTIFICATION |
DATA RECONSTR |
| CRSS |
RESISTANCE TOLERANCE PER SECTION IN PERCENT |
-5.0/+5.0 SINGLE SECTION |
| AXGY |
MOUNTING METHOD |
TERMINAL AND UNTHREADED HOLE |
| ABWV |
SHAFT DIAMETER |
0.078 INCHES NOMINAL |
| AEDX |
SHAFT STYLE |
ROUND, SLOTTED |
| AEFK |
MAXIMUM STARTING TORQUE |
5.00 INCH-OUNCES |
| CSDL |
STANDARD TAPER CURVE PER SECTION |
A SINGLE SECTION |
| ADAT |
BODY WIDTH |
0.235 INCHES NOMINAL |
| CBME |
CUBIC MEASURE |
0.047 CUBIC INCHES |
| AYQR |
CENTER TO CENTER DISTANCE BETWEEN TERMINAL ROWS |
0.100 INCHES NOMINAL |